Menu Close

C095N SPECIFIC APPLICATIONS

Category:

C095N-14
COMPRESSION TESTS UP TO 320KN CAPACITY

The multipurpose (flexural) frame can be equipped with Lower platen
and Upper spherically seated platen, having Ø 165 mm by 30 mm
thick, to perform compression tests on low strength and small size
specimens.
To be used with the four distance pieces C095N-18
The vertical useful light is from 350 to 178 mm (68mm with piston
excursion).
The device can be used also for compression tests on mortar
specimens (by using suitable devices E170 etc. listed on page 315,
splitting tensile tests (by using suitable C100, C103 etc. devices listed
on page 314).
Weight:
20 kg approx.
C095N-15
DISPLACEMENT TRANSDUCER, to measure the piston travel.
Supplied complete with holder to the test frame.
Travel: 100 mm
Full bridge at 350 Ohm
Indipendent linearity: < 0.1%
Standard sensitivity: 2 mV/V
C095N-16
ENERGY ABSORPTION TEST ON SPRAYED
CONCRETE SLABS
STANDARD: EN 14488-5
SQUARE BASE SUPPORT FRAME useful inside dimensions 500×500 mm,
holding the sprayed concrete slab, complete with spherically upper loading
element.
Weight:
125 kg approx.
NEEDED ACCESSORY
S336-14 DISPLACEMENT TRANSDUCER, to measure the central
deformation of the slab under concentrated load.
Travel: 50 mm
Full bridge at 350 Ohm
Independent linearity: < 0.1%
Standard sensitivity: 2 mV/V

C109-15N
FIRMWARE / SOFTWARE for:
Measurement of deflection on fibre reinforced concrete beams
Determination of toughness, first crack strength and ductility
Energy absorption test on sprayed specimens.
STANDARD: EN 14488-5
(see p. 283)

C095N-17
FLEXURAL TOUGHNESS OF FIBRE REINFORCED
CONCRETE (FCR) SLABS
STANDARD: ASTM C1550
BASE SUPPORT FRAME, holding the concrete slabs having 800 mm
diameter by 75 mm thick, complete with upper loading element.
Weight: 60 kg approx.

NEEDED ACCESSORY
S336-14 DISPLACEMENT TRANSDUCER, to measure the central
deformation of the slab under concentrated load.
Travel: 50 mm
Full bridge at 350 Ohm
Independent linearity: < 0.1%
Standard sensitivity: 2 mV/V

C109-15N
FIRMWARE / SOFTWARE for:
Measurement of deflection on fibre reinforced concrete beams
Determination of toughness, first crack strength and ductility
Energy absorption test on sprayed specimens.
STANDARD: EN 14488-5 | ASTM C1550
(see p. 283)

C090-15 DEFLECTION MEASUREMENT TEST on fiber reinforced
concrete beams 100x100x400(500) mm
and 150x150x500(600) mm
STANDARDS: EN 14488-3 ASTM C1609, C1018
The test is performed with the specific equipment
(deflection measurement device, displacement transducers)
described at p. 305 and the Software/Firmware
automatic system of load and displacement Servo Strain
(p. 282)

C127N GRAPHIC PRINTER on thermo-paper on board
C095N SPECIFIC APPLICATIONS
C097-05 CALIBRATION CLASS 1, starting from 1% of the full
range. With a special calibration procedure it is possible
to grant Class 1 practically on the full range of the
flexural machine.

C100 SPLITTING TENSILE test device for cylinders.
EN 12390-6 | ASTM C496
Technical details and other models: see p. 314

C115-01 TWO-WAY HYDRAULIC VALVE, connected to the motorized
pumping unit of the machine to activate a second
frame. Technical details: see p. 318

C103 SPLITTING TENSILE test device for self blocking pavers
and cubes. EN 1338, 12390-6
Technical details: see p. 314

AS AN ALTERNATIVE:
C103-02 SPLITTING TENSILE test
device for self blocking pavers and cubes,
max dimensions 300×500 mm.
EN 1338, 12390-6. Technical details: see p. 314

C093-11 DEVICE for flexural tests on
clay blocks for flooring.
STANDARD: UNI 9730-3

E170 COMPRESSION DEVICE to test mortar specimens
40.1 x 40 mm EN 196 | ASTM C349
Technical details and other models: see p. 315

Accessories for specific applications listed above are common for
different tests. We recommend to check them when ordering, to
avoid duplications.